Comparison of Wren Micro-turbojet Engine and Wren turbo-drop

Comparison of Wren little-turbojet railway locomotive and Wren turbo-dropIntro ductionIn the get hitched withing report, one volition be analysing and comparing the wren micro-turbojet locomotive locomotive and the Wren turbo-prop, the engine volition be try oned in the atmosphere laboratory in the houldsworth atmosphere laboratory, here the tests will be carried out, just before the test s be carried out on from each one of the propeller that needs to be employ for the turbo prop must(prenominal) be chosen.The propeller will be chosen in its efficiency in a certain variable which will be chosen afterward in the report, at that level is a choice of a few divers(prenominal) propellers, tests shall be ran on each different propeller with the results been recorded by the FADEC.Once the propeller has been chosen tests shall e ran on both engines, the results will be analysed with numerous variables,Health and safetyDuring the course of the lab work, wellness and sa fety will play a big commence in throwing people safe, Engines pose many a(prenominal) achievable bet ons which atomic number 18 listed downst songsNoise The engines that will be used will produce a loud noise that is capable of damaging hearing permanently wherefore the test will be wager with the testers wearing ear testimonial to prevent permanent ear damage.Fuel render poses numerous threats in the lab the highly volatile liquid can produce vaporization that can cause an explosion so thus all fuel must be kept in a sealed assumeer that must be kept sealed and stored in a cool, dry fundament away from irresponsible personnel office.Fuel is also irritable when in dawn with fur so therefore gloves must be worn when in contact with the substance.The engines the engines themselves pose a huge health and safety run a risk, the engines contain many objects in motion which can cause a hazard if any of the objects become loose, which could result in a projectile univ erse thrown across the room, to eliminate this risk, the tests will be carried out in a separate room from the testers.The engines also produce fumes which atomic number 18 harmful to humans so an extraction pipe is now given over to the exhausts to remove most of the fumes still testers must be cautious that the extraction system may non be 100% streamlined so contact time after the runs must be kept minimal.As engines must be run correctly to be run safely, inexperienced testers must always be supervised by personnel with sufficient experience with the engines.The fumes that are produced by each engine must be sufficiently vented away from the area as they are a hazard to health.Extraction system failureAt the beginning of February 2010 the convention was told that the lab where the engine runs were to be carried out had been rule unsafe due to the failure of the ventilation system had failed.It was possible that the test could not contrive been carried out, which the wh ole group was disheartened by, but the group pulled together and all tried to find a solution for the problem, many avenues were explored, even the possible opportunity of the back of a restaurant.Gareth Atkinson contacted multi line of fulfilment closely the possibility of footrace the engines at their base as it is located at Leeds-Bradford courseport, Multi flying obliged so therefore Gareth Atkinson filled out the risk opinion form shown in appendix A.By the time Multi flight replied back with their permission the group decided that that time was against us for running the engine tests at Multi flight, results from previous engine runs were used instead.The Jet EngineThe Engine has proved to be an innovative piece of machinery and has allowed the aviation industriousness to be what it is today, nearly all of the innovative cinchcraft of today and conceptual appearancecraft of tomorrow are all provideed by the same type of engine the jet engine.The depression form of jet propulsion device was first patented by a French engineer Ren Lori in 1913 but the design remained conceptual as the design needed in fervor resisting materials that were not available at the time plus the reason that the jet engine was not suitable to fly at the low airspeeds as they did at the time (1996a) The design of which is shown in figure 1.Not until 1930 did frank cut receive a patent for a jet engine, Frank whittle went on to build the first jet engine which had its maiden flight 11 years after its patent was received. From this basic foundation more than advanced jet engines were produced.Since this first prototype the jet engine has demonstrable from this early prototype to effect aircraft that travel faster than sound. The jet engine works by compressing air adding fuel and combusting the mixture development the wardrobe increase to accelerate the air back out of a propelling nozzle.The compression is the first salute of a bollix turbine engine, there are many different configurations of compression the first form was the outward-moving compressor, which is the same compressor is fitted to the Wren micro- shooter turbines that will be tested in this dissertation.motor(a) compressorThe centrifugal compressor essentially does what it says on the tin and compress the air exploitation centrifugal push ups, the air is compressed by an impeller which is attached and rotated by a creature that is connected to the rear turbines, which convert the pressure level, upper and heat nada from the exiting gas in to mechanical energy to rotate the radiation which turns the impeller at high speed.The air introduced continuously throughout the running of the engine through to the eye of the impeller which then enters the rotating guide vanes and due to centrifugal forces causes the air to move towards the tips of the impeller here the air enters the diffuser which is a system of stationary(Rolls-Royce Limited., 1996) ducts which are designed t o convert the kinetic energy of air stream into potential energy, which further increases the pressure of the gas. Below is a diagram showing a cross- segment of the impeller and the changes in pressure and velocity throughout the impellerFrom figure 2, the interpret at the right shows the pressure and velocity changes at each stage of the centrifugal compressor, as the air enters the eye of the impeller. The air is subjected to a cartridge extractor which increases the pressure and velocity of the airstream, the air then passes through to the diffuser section where the passage of divergent nozzles convert the kinetic energy into pressure energy. The graph shows that half the pressure rear occurs in the impeller and the other half in the diffuser section. (Rolls-Royce Limited., 1996).Axial merge compressorsAxial flow compressors have a higher compression ratio than centrifugal compressors provided air which is at a higher pressure therefore used over centrifugal compressors as the higher pressure give better performance.Axial flow compressor consists of alter rotor and stator blades, where each stage, which consists of a row of rotating blades followed by a row of stator blades, increases the pressure by a small meter so therefore several stages are infallible to give the pressure increase ask. Where many stages of compression engage on one shaft it becomes necessary to vary the stator vane angle to enable the compressors to hold out effectively at speeds below the design conditions. (Rolls-Royce Limited., 1996).A single bobbin compressor consists of one rotor assembly and stators with many stages as required achieving the sought after pressure ratio, a multi-spool compressor of two or more rotor assemblies, each driven by their own turbine at an optimum speed to achieve higher pressure ratios and to give greater operating flexibility. (Rolls-Royce Limited., 1996).Principles of mental solveDuring mental process the rotor is turned at high speed s by the turbine which makes sure that air is constantly be inducted into the compressor, which then is accelerated by the rotating blades and swept rearwards into the adjacent row of stator vanes. The pressure increase results kinetic energy received by the air by the rotor vane, which is then decelerated (diffused) by the stators vanes turning the kinetic energy into pressure. (Rolls-Royce Limited., 1996).Combustion ChamberThe fire sleeping room has the task of burning large quantities of fuel supplied through the fuel disperse nozzles, with large volumes of air supplied by the compressor and releasing heat in a controlled process that the air is expanded and accelerated to give a debonnaire stream of uniformly heated gas at all conditions required by the turbine. The amount of fuel added will depend on the temperature rise required although the maximum temperature is limited by the materials that make the turbine blades and nozzles. (Rolls-Royce Limited, 1996)The fire proc essThe air arriving from the compressor is travelling at speeds up to 500 feet per second, which if entered the domiciliate would beat out the beam due to the airs high velocity, so therefore the air must be decelerated. The air is diffused so the velocity is reduced also giving the added benefit of increasing the pressure. (Rolls-Royce Limited., 1996).IIn normal operation the overall air/fuel ration can vary amid 451 and 1301, however kerosine will still burn efficiently at, or close to, a ratio of 151, so the fuel must be burned with only part of the air entering the chamber, in what is called the primary electrocution zone. This is achieved by center of a beam tubing that has various devices for metering the airflow distribution on the chamber. (Rolls-Royce Limited., 1996).As shown in Figure 4, 20% of the air mass flow enters at the snout of the chamber, immediately downstream are a perforate flame and swirl vanes, the swirling air induces a flow upstream of the snappe r of the flame pipe and promotes desired re-circulation. (Rolls-Royce Limited., 1996).Through the wall of the flame underpass body, next to the combustion zone, are a fig of secondary holes were a further 20% of the main flow of air passes into the primary zone. The air from the swirl vanes and that from the secondary air holes interacts and creates a region of low velocity recirculation, this take the form of a toroidal vortex, very similar to a smoke ring, this helps stabilise and anchor the flame the flame. (Rolls-Royce Limited., 1996).The temperature of the gases after combustion is almost 1800 to 2000C, which is far too hot for entry to the nozzle guide vanes of the turbine. As only 40% of the total airflow is used in the combustion process, so the 60% is left to help cool the air, which is introduced progressively into the flame tube. Approximately a third of this is used to cut back the gas temperature in the dilution zone before it enters the turbine, whilst the remaind er of the air is used for cooling the walls of the flame tube. This is achieved by a film of cooling air flowing on the inside surface of the flame tube, insulating it from the hot combustion gases. (Rolls-Royce Limited., 1996).Types of combustion domiciliateThere are three main types of combustion chambers used in gas turbine engines these are multiple chambers, turbo-annular chambers and annular chamber. three-fold combustion chambersThis type of Combustion chamber is used on centrifugal compressor engines and primitive axial flow engines. The chambers are sell more or less the engine and compressor delivery air is directed by duct to pass into the one-on-one chambers. Each chamber has an internal flame tube around which there is an air casing, the air passes through the flame tube snout and also between the tube and the outer casing as earlier described. All the flame tubes are all interconnected which allows them to operate at the same pressure and also allows combustion to propagate around the flame tubes during engine starting. (Rolls-Royce Limited., 1996).Tubo-annular combustion chamberThe tubo-annular combustion chamber tie the evolutionary gap between the multiple and annular types. A number of flame tubes inside a common air casing. (Rolls-Royce Limited., 1996).Annular combustion chamberThis type of combustion chamber consists of a single flame tube in a completely annular form, which is contained in an informal and outer casing. The main advantage of the annular system is that for the same power output, the length of the chamber is 25% shorter than the tubo-annular system for the same diameter, saving take and production costs. . (Rolls-Royce Limited., 1996).Combustion chamber performanceA combustion chamber must be capable of allowing fuel to burn efficiently over a wide range of operating conditions without incurring large pressure losses. Also if flame extinction occurs, then it must be possible to relight. . (Rolls-Royce Limited., 1996). TurbinesThe turbine has the job of providing the power to drive the compressor and accessories and sin some engines shaft power for the propeller or rotor. This is done by extracting energy from the hot gases from the combustion system and expanding them to a lower pressure and temperature. The turbines are subjected to high stresses with the turbine tips speeds stretching over 1,500 feet per second with gas temperatures.Types of turbinesGas turbine manufacturers have concentrated on the axial flow turbine, although some manufacturers are building engines with a radial-inflow turbine. The radial-inflow turbine has the advantages of being rugged, simples and relatively inexpensive and easy to manufacture compared to the axial flow turbine. On this type of turbine, inlet gas flows through the peripheral nozzles to enter the flap passages in an inward radial means. The speeding gas exerts a force on the wheel blades and exhausts the air in a radial direction to the atmosphere. These turbine wheels, used for small engines, are well suited for a lower range of specific speeds and work at relatively high effieciency.Micro turbines in industryIn this section I will cover and analyse the role of micro turbines in industry within aviation and out of aviation.Micro turbines can be used to produce electricity as well as power some ships.WREN ENGINESIn this section I will be analysing the company of WREN, I will include what they do, their history and the current situation.I will note that the workers are enthusiast and work at a minimal wage to keep the company in business.WREN turbo propIn this section I will analyse the turboprop that will be tested in more detail.I will go through each luck in a fair amount of detail, I will go through the manufacture process in some detail, and analyse the materials that are used.Wren turbo jetHere I will do in the same format as the turboprop but with a daybook of our engine build here is some rough notes I have made of the e ngine build 26/10/09Did our Risk opinion with Chris brier, told info on all scenery.Got on to the engine build, went smoothly until tincture 11 when inserting the shaft into the middle we dislocated bearings due failing to follow a step properly.We immediately called Chris brier to help us with our print he showed us how to replace the ball bearings into place.We then progressed onto the next step, at this point we saw etchings on the shaft and the rear turbine which we asked why they we interchangeable soWe learnt that they were there for mass balancing, as an imbalance in weight down would cause the shaft to distort.Balancing is done on each individual shaft by the manufacturer by a machine.Another aspect of the is the inefficiency of the compressorCompared to lager jet engines the gap between the edge of the compressor blades and outer skin is comparatively large therefore not all of the compressed air is used for the production of thrust, some leaks behind the compressorSt ep 16- when fitting turbine shrouds the turbine rests on a rim and not on turbines.Step 17- aligning field front, case front has been checked and aligned to the best of our abilities.Step 21- chamber stand-offs successfully crimpedStep 22- comb chamber fixed in place, gas and oil tube is place and 3 stand-offs screwed inWe found that the gas tube didnt fit because of misaligned lubrication pipe. So backtrack in progress was required to re-configure this step.In the process of correcting the combust chamber bearings in the same place fell apart, so were back to the same stage again abbreviationThis section I will analyse the results in detail valuationEvaluate the whole processconclusionAppendiCiseApendix AMulti-flight risk assessment formRolls Royce PLC. (1996a). The Jet Engine (5th Edition ed.). Birmingham Renault Printing Co Ltd.